INSTALLATION AND OPERATING INSTRUCTIONSCS/CSM SERIES RESIDENTIALWATER SOFTENERSMODELS:CS1001 CSM1001 CS1501 CSM1501 CS2001 CSM2001 INSTR2201 031
INSTRUCTIONS FOR USING REGENERATION FREQUENCY SCHEDULES: (Time clock initiated models only) 1) Determine ADJUSTED HARDNESS by adding three (3) times
3-2REGENERATION FREQUENCY SCHEDULES (Cont'd)(TIMES PER 12 DAYS)Model CS2001PersonsinFamilyHardness -- GPG5 10152025303540455055606570758085901 11
HOW TO SET TIME CLOCK REGENERATION CONTROL 3-3HOW TO SET DAYS ON WHICH WATER SOFTENER IS TO REGENERATE: Rotate the skipper wheel until the number &quo
The regeneration cycle program on your water softener has been factory preset, however, portions of the cycle or program may be lengthened or shortene
HOW TO SET METER REGENERATION CONTROL 3-5TYPICAL RESIDENTIAL APPLICATION: To program, just set the time, set the hardness and it automatically monitor
REPLENISHMENT OF SALT SUPPLY: The salt storage capacity of the brine tank is approximately 160 lbs (72.6 kg). During each regeneration a specifi c amou
5-1SECTION 5: SERVICE INSTRUCTIONS PROBLEM POSSIBLE CAUSE SOLUTION1 Hard water, (unit not using salt; liquid level in brine tank not too high).A. Elec
6-1NOTES:1) Actual capacity may vary substantially depending on water analysis and operating conditions. 2) For satisfactory performance indicated
7-1SECTION 7: PARTSCOMPONENT PARTS LISTTWO TANK MODELS (CS & CSM SERIES)46513213149111210781516REF NO. DESCRIPTION CS1001CSM1001CS1501CSM1501CS200
7-3CEC 1000 SERIES SOFTENER CONTROL - 12 DAY TIME CLOCK
SAFETY INFORMATIONRead, understand, and follow all safety information contained in these instructions prior to installation and use of the Aqua-Pure®
ONLY THOSE PARTS CIRCLED IN DRAWING AND/OR LISTED BELOW ARE STOCK ITEMSALL OTHERS ARE SPECIAL ORDER, NON-RETURNABLEPARTS LIST - 12 DAY TIME CLOCK 7-3P
CEC 1000 SERIES SOFTENER CONTROL - METER INITIATED 7-4
7-5ONLY THOSE PARTS CIRCLED IN DRAWING AND/OR LISTED BELOW ARE STOCK ITEMSALL OTHERS ARE SPECIAL ORDER, NON-RETURNABLEMETER INITIATED PARTS LIST PART
WIRING DIAGRAM FOR VALVE DRIVE MOTOR AND Time clock CEC 1000 SERIES VALVES 7-6VALVE MOTORTIMER MOTORPROGRAMWHEELPROGRAMRE-SETSWITCHWHITEBLUERAPID RINS
SECTION 8: LIMITED WARRANTYLimited Warranty: 3M Purifi cation Inc. warrants this Product to be free from defects in material and workmanship during no
TABLE OF CONTENTS SECTION DESCRIPTION 1 BEFORE INSTALLATION 2 INSTALLATION 3 REGENERATION INSTRUCTIONS 4 MAINTENANCE 5 SERVICE INSTRUCTIONS 6 SPEC
1-2Check Your Pumping Rate and Water Pressure:Two water system conditions must be checked carefully to avoid unsatisfactory operation or equipment dam
Facts to Remember While Planning The Installation: 1) All installation procedures MUST conform to local and state plumbing codes. 2) If lawn spr
SECTION 2: INSTALLATION2-1Figure 1. Typical Installation Sequence Of Water Conditioning EquipmentWATER SOFTENERBACKWASHFILTERSOFT WATERTANKSWITCH.PR
Step 1If not factory pre-installed, attach bypass valve or yoke assembly using adapter couplings, clips and screws to control valve (Figure 2). On me
Step 5Attach drain line to drain line fi tting. To prevent back pressure from reducing fl ow rate below minimum required for backwash, drain line must
Step 13Set time of day (refer to appropriate How To Set Time Clock/Meter Regeneration Control, Section 3). When shifting to daylight saving time (and
Comments to this Manuals